Quick Answer: What replaced 939-001814?
Discontinued: 939-001814 | Replacement: 952-000080
Why LOGITECH Discontinued the 939-001814
Logitech 939-001814 is in EOL progress, with limited distributor stock remaining. No official reason or end date has been published for 939-001814.
Based on available research, LOGITECH has announced 939-001814 as End of Life in progress rather than fully unavailable. That means 939-001814 may still be purchased through some distributors while remaining inventory lasts, but buyers should expect stock to tighten over time.
It is important to note what has not been confirmed. Logitech sources reviewed do not state a formal discontinuation reason for 939-001814, and no published EOL date has been announced. There is also no manufacturer-source confirmation naming 952-000080 as the official direct successor to 939-001814. However, for procurement and replacement planning, 952-000080 is being positioned here as the practical replacement option based on the available comparison data tied to the active Tap Table Mount form factor.
For IT buyers managing meeting room hardware, the key takeaway is straightforward: if your standard build includes 939-001814, now is the time to review current deployments, check remaining stock, and qualify 952-000080 before availability on 939-001814 becomes more constrained.
What's New in the 952-000080
Lower overall height
The most visible change from 939-001814 to 952-000080 is height. The 939-001814 measures 4.01 in (102 mm), while 952-000080 measures 2.4 in (61 mm). For conference table installations, this gives 952-000080 a noticeably lower profile than 939-001814.
Reduced display angle
The 939-001814 uses an elevated viewing position of about 30 degrees, while 952-000080 uses a 14 degree low-profile angle. In practical terms, 952-000080 sits flatter on the table than 939-001814. That may better suit rooms where a lower visual footprint is preferred, but teams used to the more elevated 939-001814 viewing position should verify ergonomics before standardizing on 952-000080.
Similar width for fit planning
Width remains the same between 939-001814 and 952-000080 at 9.6 in (244 mm). If your room design, furniture cut sheets, or accessory spacing were based on the width of 939-001814, the matching width on 952-000080 should simplify transition planning.
Slightly deeper footprint
The 939-001814 has a depth of 6.9 in (174 mm), while 952-000080 is listed at 7.0 in (179 mm). This is a small change, but it is still worth checking against table edge clearances, cable routing paths, and shared tabletop space when replacing 939-001814 with 952-000080.
Replacement positioning caveat
One important point for technical buyers: the research supports these dimensional differences versus the active Tap Table Mount design, but it does not include a Logitech statement explicitly confirming 952-000080 as the official replacement part for 939-001814. If you need strict manufacturer confirmation for compliance or internal documentation, you should record that limitation during your sourcing review.
At-a-Glance Comparison
| Feature | 939-001814 | 952-000080 |
|---|---|---|
| Manufacturer | LOGITECH | LOGITECH |
| Status | EOL in progress | Replacement option |
| Height | 4.01 in (102 mm) | 2.4 in (61 mm) |
| Display angle | ~30° (elevated for visibility) | 14° (low profile) |
| Width | 9.6 in (244 mm) | 9.6 in (244 mm) |
| Depth | 6.9 in (174 mm) | 7.0 in (179 mm) |
| EOL date | Not announced | Not applicable |
| Discontinuation reason | Not stated in available sources | Not applicable |
Upgrade Checklist
- Audit installed base: Identify every room, quote, and standard configuration that currently uses 939-001814.
- Check remaining supply: Since 939-001814 is EOL in progress, confirm distributor stock before committing to refresh or expansion plans.
- Validate fit: Compare the lower 2.4 in height and 14 degree angle of 952-000080 against the taller 939-001814 user experience.
- Review tabletop clearances: Even though width is the same, confirm the slightly deeper 952-000080 footprint works in your room layouts.
- Document sourcing notes: If your procurement process requires manufacturer-backed succession data, note that publicly available research does not confirm 952-000080 as an official Logitech-designated successor to 939-001814.
- Standardize future orders: If testing is successful, shift new purchasing from 939-001814 to 952-000080 to reduce last-time-buy risk.
- Coordinate with stakeholders: Let AV, IT, and facilities teams know that 939-001814 availability may decline and that 952-000080 should be evaluated for ongoing room deployments.
Bottom Line
LOGITECH 939-001814 is in End-of-Life progress, with limited stock still available and no published EOL date. For buyers moving away from 939-001814, 952-000080 is the practical replacement option to evaluate, especially if a lower-profile mount is acceptable.
The main differences between 939-001814 and 952-000080 are height and display angle, while width remains the same. If you are planning room upgrades or need to secure continuity for future deployments, it makes sense to qualify 952-000080 now.
Ready to switch? Shop 952-000080 →
